Car Key Button Repair<br /><br />A damaged car key button can be frustrating. You might need to call an emergency locksmith service 24 hours a day to assistance or purchase a replacement remote.<br /><br />However, you might be in a position to save money by repairing a worn-out key fob instead of replacing it. This is especially true when a worn-out switch or faulty contacts are at the root of the problem.<br /><br />Battery<br /><br />If the buttons on the key fob aren't responding to pressing, this could be a clear indication that the battery is dying or nearing the end of its life. It's easy to replace the battery yourself, rather than paying for an auto locksmith or dealership.<br /><br />Find the battery compartment first. It is usually located on the backside of the key fob and might be hidden behind the cover, which slides out, or an access point that opens when you push the button. When the compartment is open then you will find the small cell battery. It's usually shaped as a coin and marked with an minus and plus sign. Remove the battery that is old and replace it with a brand new one. Check that the plus and minus symbols are aligned correctly.<br /><br />Close the compartment and snap the two parts of your key fob. Before closing the door make sure to align and snap the parts in the correct position. Press any of the buttons to verify that they function properly.<br /><br />If your remote key fob stops functioning even after replacing the battery, it might be suffering from other issues that require a different form of repair. The fob's dropping in a puddle could cause it to stop functioning. It could also be a problem with the internal electrical system or the need to be deprogrammed. Try to figure out if the issue is with your key fob applying these other typical automotive troubleshooting methods.<br /><br />Switches<br /><br />Based on the year and the model, there are a variety of types of switches on the keyfob of your car. <a href="https://rentry.co/yg6w3uog">remote car key repair</a> have an embedded chip that can be seen in the case. The newer keys work by sending signals to your car. The buttons on a key can be damaged or worn out due to normal use, regardless of the type. They can become difficult to press or not responsive. If you press the button too hard, it could cause further damage. It may also prevent the key from functioning in the future.<br /><br />If you're unable to get your key to work Try changing the batteries. If that doesn't work then you might need to clean the key's fob and re-adjust the switches. These tiny electronic switches are more susceptible than larger components of the key to break since they are constantly jostled.<br /><br />The switches are rubber-like, and are coated with an electricity conducting film that wears down over time. Luckily, they're also a very small part and cheap to replace. They're soldered on the circuit board, which means it is important to remove the old ones without causing any damage to any other part of the circuit. Then, you can solder the new ones into and reassemble the fob.<br /><br />An effective way to protect your car key fob from getting damaged is to not use it for longer than a couple of hours at a time, and to avoid leaving it in visible locations that it will be visible. When you're not using your key, put it away in a safe place.<br /><br />If you've already tried cleaning your key fob and replacing the battery, and the issue continues to persist, it may be time to consider a locksmith. A professional locksmith can check your key's frequency to see if your vehicle is still able to communicate. They can also open and replace microswitches, change cases, and much more.<br /><br />Outer Case<br /><br />A key fob spends much of its time bouncing around and when the buttons aren't able to move upwards and downwards within the case they can get stuck or broken. If cleaning the case with rubbing alcohol and a cotton swab fails to work, it could be necessary to remove the case. If the contacts where the buttons touch aren't fitting well or are worn out, adjusting them might be the only solution to correct the issue.<br /><br />Rubber buttons can get worn out over time. Rubber buttons can become hard to press when they stretch, and nails can gouge them. In this scenario the key could fail and it's time to replace the case or the buttons. This repair involves disassembling the remote, locating the button switches on the circuit board, heating up the solder and carefully removing them. New buttons are then attached to the circuit board. The case can be rebuilt and the horseshoe key blade can be inserted. The new buttons must be a close fit inside the case to avoid them from falling out.<br /><br />Inner Case<br /><br /><br /><br />Over time the buttons on your key fob could be damaged or stuck as a result of the constant jolting and accidental pressing. If your key fob stops working when you are away from home You can solve the issue quickly using metallic tape and punch holes. This will allow you to unlock doors but not start your vehicle. This simple fix will enable you to safely get back to your car and finish your trip.<br /><br />