The process of installing a cat flap may be a bit daunting but it's simple to install with the proper instructions. Determine how high you would like the flap to be (normally, it is at belly height). Then, mark this area on the door and use the template provided as a reference to drill.<br /><br />If you have a small kitten hold the door open a bit and gradually allow it to enter. Reward it as it passes through.<br /><br />Measure the Door<br /><br />A cat flap is a wonderful option to let your pet leave and come in and out of your house as it pleases. This will keep your cat in good health as it ensures that it gets enough exercise and will also allow it to go back inside if it is trapped outside during bad weather. It can also cut down on the amount of time you have to let it out or in. It will also help keep your home safe by letting you know when it's been out.<br /><br />It is important to ensure that the cat flap is installed properly to stop your pet from being pushed through or escaping through it by other animals (e.g. dogs). It is crucial to determine the height of your pet's belly and the doorway to your home so that you can ensure that the flap is at the right height. If your cat is taller or shorter than normal, you can adjust the flap's height by moving it up or down by a tiny amount.<br /><br />The next step is to use a spirit level to mark the middle of the door. This is where you will install the flap. Then, using the marks as a guideline, cut out the form of the flap on the door with a Jigsaw. After you've cut the space, sand down the edges of the door to smooth the surfaces. Then drill any fixing holes that are required.<br /><br />The process of installing a cat flap is not as complicated as you think and it should not take more than two hours to finish the entire job from start to the end. The process can be slightly more challenging if you need to install it on the case of a uPVC door or composite one. This is due to the fact that these doors come in a variety of thicknesses, which can impact the way the holes are cut. This is the reason we recommend hiring a professional to carry out the task, especially if you have never worked with glass before.<br /><br />Measure Your Cat<br /><br />You can avoid hours of listening to the pet meow to be allowed in or out. This is especially helpful when your cat is inside during the winter months when you are at work.<br /><br />It is crucial to measure your cat first before attempting to install. It might appear to be a simple task, but it is essential to get the measurements right. In the event that you don't, your cat may find it difficult to use.<br /><br />First, make sure your cat is calm before you begin taking measurements. You'll need to keep your cat in a position in which they cannot move. Also, make sure that the measuring tape is straight and not bent against the body. Keeping the ruler or measuring tape against their body from the top of their head to the tip of their tail will enable you to get an precise measurement.<br /><br />Once you've figured out the measurements of your cat, it's time to take a look at the door and decide where to place the flap. The flap should be placed at the level of your cat's belly. This will allow them to walk through the door without much effort. This will also prevent the flap from making a lot of noise when it swings back and forward.<br /><br />You should consider the thickness of the uPVC or composite door, as well. While timber doors are all of a similar thickness, uPVC and composite doors can be very different in their overall design and can make fitting a cat flap more complicated as you will need to ensure that the hole you cut is the correct size for your pet.<br /><br />You can also use the template included in the instructions to mark the position of the hole on the door. This will help you determine where the opening must be and make sure the template is placed correctly on the door. Using a spirit level to make sure that the template is right against the door will also prove beneficial.<br /><br />Cut <a href="https://www.repairmywindowsanddoors.co.uk/camberley-cat-flap-installer-near-me/">cat flap installation</a> will need to cut a hole in the door to accommodate your cat flap prior to you can attach it. This can be a challenging job and it is recommended that you get help from an expert cat flap fitter for this step in case you don't have the expertise or knowledge to complete the task yourself. It is also recommended that you read the instructions included with the cat flap kit to learn how to do this properly.<br /><br />You can use the height of your cat's or kitten's stomach as a guide. A good guideline is to place the cat flap about 10-15 centimeters from the ground as this is approximately the average belly height for cats. This will allow your cat to move through the flap without difficulty and will make it difficult for other cats or naughty neighbors to get in or out.<br /><br />The position of the cat flap on the door using a pencil. Next, if your kit comes with a paper template, lay this over the door and use the marks to drill holes in each corner of the template. You will then be able to cut out the shape of the template and replace it with your cat flap.<br /><br />If you are installing your cat flap in the form of a door made of wood or uPVC, you can do this yourself if you are comfortable with using a jigsaw. Be sure to not cut through any of the door mullions or vertical rails. You can use a jigsaw cut the panel into a circle or square depending on the design of your cat flap. Be patient, and don't try to force the jigsaw to cut faster.<br /><br />Once the hole is made, carefully place the cat flap in its new home. Make sure that it is solidly secured. If the flap is fitted with screw caps, push them onto the protruding bolts. Once the screws are in place, sand the rough edges of the cut, and then apply sealant around any gaps to ensure that there aren't any draughts entering into your home.<br /><br />Fit the Flap<br /><br /><br /><br />If you have a basic cat flap, you can open it and encourage your pet to walk through by putting a small amount of cat food in the front of the door. Alternately, you can push the cat through with your hands or with a stick. Once your cat is accustomed to moving through the flap, it will be capable of walking through the flap whenever it wants. This will allow you to let it in and out as it wishes.<br /><br />It is possible to fit a cat flap into a UPVC or glass door although this may not be as simple as fitting it into a wooden exterior door due to the fact that UPVC and some glass doors don't have the same thickness. This can have a dramatic effect on the way you cut the hole for the flap and could affect the way your flap is fitted correctly after it has been put in place.<br /><br />The mounting kit may contain a template that outlines where to drill holes. If the kit doesn't come with the template you can use a photocopier to make your own. When cutting, it's important to keep the jigsaw from being pushed too far enough to make a larger hole than necessary in your door.<br /><br />Some cat flaps come in circular designs, which are more difficult to put in. If you have a circular flap, it's essential to make sure the hole is in the correct position on your door, because if it's not, the cat will not be able to use the flap and may be stuck outside all day (or even at night).<br /><br />Some cat flaps come with locks that permit you to regulate when your cat comes and goes. They can be extremely useful if you're worried about your cat going out at night and then coming back in because of the darkness, or you're working all day. Certain locks can be used to lock access or exit, and others can be locked in both directions. This is helpful for sick or older cats who don't want to venture out in cold weather.<br /><br />