Car Key Button Repair<br /><br />A damaged car key button can be frustrating. You may need to contact the 24 hour Locksmith Service or purchase an alternative remote.<br /><br />But, you may be saving money by repairing an old key fob instead of replacing it. This is especially true if the issue is caused by an old switch or a damaged contact.<br /><br />Battery<br /><br /><br /><br />If your key fob's buttons are not responding to your pressing them, this could indicate that the battery has died or is close to the end of life. It's simple to replace the battery yourself instead of hiring a locksmith or dealership.<br /><br />Locate the battery compartment first. It is typically located on the backside of the key fob and might be hidden behind a slide-out cover or an access point that opens when you press the button. When the compartment is open then look for the small button-cell battery. It's usually the shape of an ordinary coin and is has a plus and minus symbol. Take the old battery out and replace it with a new one. Check that the plus and symbol are aligned correctly.<br /><br />Close the compartment and snap together the two parts of your key fob. Before closing the door make sure to align and snap the parts into the correct position. Press any of the buttons to ensure that they work properly.<br /><br />If your remote key fob ceases working after replacing the battery, it could be experiencing other issues that require a different kind of repair. Dropping the device into a pool of water can cause it to cease functioning. It could also be due to a malfunction with the internal electrical system or need to be deprogrammed. Find out if the problem is related to your key fob using these other common car troubleshooting techniques.<br /><br />Switches<br /><br />There are a variety of switches found in the car key fob dependent on the year and make. The older style keys have an electronic chip that is visible inside the case. The newer keys work by transmitting signals to your car. The keys' buttons can be damaged or worn out through normal use, regardless of the type. They become difficult to press or not responsive. If you try to press the button too hard the button, it could cause damage, and could even prevent the key from starting your vehicle in the future.<br /><br />If your key doesn't appear to be working, you should first try changing the battery. If this doesn't work, you might need to clean the key fob or adjust the switches. Since these tiny electronic switches spend a lot of time being tossed around and tangled, they are more likely to wear out than larger components of your key.<br /><br />The switches are rubber-like, and are coated with an electricity conducting film that can wear down over time. However, they're a small part that is easy to replace. They're soldered to the circuit board, which means you need to carefully remove the old ones without causing any damage to any other part of the circuit. Then you can put the new ones in and put them back together.<br /><br />Don't use your car key fob for more than two hours at a stretch and don't leave it out in the open. If you don't use your key, put it away in a safe place.<br /><br />If you've already tried cleaning your key fob or replacing the battery, and the problem persists it's time to think about hiring an appointment with a locksmith. A professional locksmith can check your key's frequency to see whether your car is capable of communicating. They can also open and replace microswitches, alter cases, and much more.<br /><br />Outer Case<br /><br />If the buttons can't move freely in the case, they may be stuck or even break. If replacing the battery or cleaning with an alcohol-based swab and a cotton pad alcohol rubbing doesn't solve the issue, then removing the case and inspecting may be necessary. If the contacts the buttons touch are not a good fit or are worn, changing them might be the only solution.<br /><br />Some keys are equipped with rubber buttons which can wear out over time. Rubber buttons can become difficult to press when they stretch, and nails can scratch them. In <a href="https://rees-cortez.technetbloggers.de/its-time-to-upgrade-your-broken-car-key-repair-options">try what she says</a> could fail and it's time to replace the case or buttons. This repair involves disassembling the remote, finding the button switches on the circuit board, heating up the solder, and then carefully removing them. The circuit board is then soldered with new buttons. The case can be rebuilt, and the horseshoe key blade can be attached. The new buttons should be a close fit into the case to prevent them falling out.<br /><br />Inner Case<br /><br />Over time, your key fob's buttons can be damaged or stuck because of the constant jolting and accidental pressing. With the help of metal tape and a hole-punch, you can often quickly fix this problem in the event your car is away from home when the key fob won't work and allows you to open the doors, but not to start the engine. This simple fix can allow you to safely get back to your car and continue your journey.<br /><br />